Merlyn435 Flight Stack

This is my custom Merlyn435 Flight Stack! This project was made as a successor to my previous Merlyn411 flight controller due to several limitations. It lacked in its processing power and free UART ports. Its mounting pattern was also unconventional at 25mm, making its mounting incompatible with any ESCs on the market. By upgrading to the AT32F435@288MHz, the new Merlyn435 easily handles 8k8 PID loop and advanced autonomous flights with 3 spare UART ports.

The Merlyn435 also upgrades the IMU from the MPU6500 to the LSM6DSK320X, which provides significantly better vibration noise rejection at $3.8\text{ bsp;}\mathrm{mdps}/\sqrt{\mathrm{Hz}}$ compared to $10\text{ bsp;}\mathrm{mdps}/\sqrt{\mathrm{Hz}}$. This results in cooler motors and more stable flights with fewer gyro filters, preventing issues such as mid throttle oscillation and flyaways.

The Merlyn435 flight controller is designed for a wide battery voltage ranging from 2 to 6 cells. This flight controller can also be mounted in various sizes of drones from 2" to as big as it can get.

It is a 3 in 1 flight controller offers features such as an integrated 2.4GHz ExpressLRS receiver and an OSD to overlay telemetry directly in the video feed. Furthermore, it has 16MB of flash memory for blackbox logging to assist in flight tuning.

The MerlynESC is a 4 in 1 ESC which runs on Bluejay firmware and also operates from 2 to 6s battery voltages. Its maximum continuous current is 40A per motor and peaks up to 55A for a maximum duration of 10 seconds.

• MCU: AT32F435CGU7
• IMU: LSM6DSK320X @ SPI1
• Barometer: BMP388 @ 0x76
• OSD: AT7456E @ SPI2
• Blackbox: W25Q128JV 16MB Flash @ SPI2
• Receiver: Serial ExpressLRS (ESP8285 + SX1281) @ UART2
• Voltage range: 2-6s LiPo / Li-ion / LiHV
• Power Supply: LMR51420YDDCR buck converter + SPX3819M5-L-3-3 LDO
• Mounting: M2 20x20mm

• MCU: EFM8BB21F16G
• MOSFET: JMSL0302AU
• Gate Driver: EG6288
• Max Current: 145A Peak / 40A Continuous @ 1.2mΩ
• Voltage range: 2-6s LiPo / Li-ion / LiHV
• Power Supply: HT75C0-1 12V LDO + HT7533-1 3.3V LDO
• Mounting: M2 20x20mm

Because the Merlyn435 is a custom hardware layout with no existing Betaflight targets, you must compile Betaflight using the custom target definitions in /firmware/source/betaflight or use the pre compiled firmware of your preferred Betaflight version in /firmware/binaries

1. Clone the betaflight repository using any UNIX terminal (use MSYS2 MINGW64 on Windows) and enter the directory
2. Enter make configs (install any required GCC toolchain if asked)
3. Create a directory in betaflight/src/config/configs named MERLYN435 and paste config.h in the new directory

• For v2026.6 and later, create a directory in configs named "ANSN" before creating the MERLYN435 directory inside "ANSN"

4. Enter make MERLYN435 and the .hex file should appear in betaflight/obj

1. Clone the iNav repository using any UNIX terminal (Building iNav is not supported on Windows) and enter the directory
2. Switch to the latest iNav stable release. E.g. git checkout 9.1.0
3. Create two directories. One named build in the root directory and another named MERLYN435 in /src/main/target
4. Copy CMakeLists.txt, target.c and target.h into the MERLYN435 directory from /firmware/source/inav
5. Enter the build directory
6. Enter cmake .. (install any required GCC toolchain if asked)
7. Enter make MERLYN435 and the .hex file should appear in /build

1. Via USB DFU Mode (Recommended): Short the SWD B test point to 3.3v and plug in the USB C cable. Open Betaflight Configurator (applicable for iNav), select your compiled local .hex file, and click Flash Firmware.
2. Via SWD: If the bootloader is corrupted, connect an ST Link programmer to the B, D and C test points (R is optional) and flash the compiled binary with STM32CubeProgrammer.

The internal ESP8285 ExpressLRS receiver is wired to the AT32 via UART2. It uses the BETAFPV 2.4GHz Lite RX firmware target. The firmware binaries can be obtained from the ELRS site or from this repository in /firmware/binaries. There are two way to flash the receiver:

Note that Betaflight must be installed and configured before passthrough works.

1. Bridge the BOOT pad

2. Connect the FC via USB
3. Open the ExpressLRS Configurator web flasher or app
4. Select Receiver
5. Select your preferred firmware version and the BETAFPV 2.4GHz Lite RX target and press next
6. [OPTIONAL] Enter your bind phrase
7. Select the Betaflight Passthrough flashing method, press next and follow the steps

If the ESP8285 is bricked or passthrough fails, you can flash it directly using an FTDI adapter or another ESP8285/ESP8286/ESP32 or even an Arduino. Bridge R to GND as well as the BOOT jumper and connect the FTDI TX to RX and FTDI RX to TX

The MerlynESC is a 4 in 1 ESC that runs Bluejay firmware target A, MCU type H, 30x20.4ns deadtime and 48KHz PWM frequency. The firmware files can be found in /firmware/binaries or the official Bluejay repository. You can flash the EFM8BB21 chips using the C2 programming pads with a makeshift arduino programmer.

While this project is mainly focused on the Merlyn435 + MerlynESC flight stack, I also designed a high performance 3 inch freestyle FPV drone. If you want to recreate the full build, below is the component breakdown:

• Frame: RATE S30 Pro carbon fiber frame
• Motors: RATE 1505 4300KV
• Propellers: HQProp 3x3x3
• Camera: Caddx Ratel 2 analog camera
• VTX: Cyclone 1W analog video transmitter
• GPS: RATE M10 GPS module
• Battery: GNB 4S 850mAh 120C LiHV
• Fasteners (If using CF frame): Included with frame kit
• Fasteners (If using 3d printed frame):
  • 6x M3 20mm Female to Female Brass Standoffs
  • 12x M3 6mm Screws
  • 4x M2 Nuts
  • 4x M2 20mm Screws
  • 8x M2 10mm Screws
  • 16x M2 6mm Screws
  • 4x M2 6mm Screws
  • 8x M2 6mm Self Tapping Screws

I advise against 3D printing your frame. On my previous build, a 100 percent infill PETG frame shattered from a very light fall. More importantly, 3D printed frames flex and resonate which causes excessive gyro noise and leads to deteriorated flight performance.

The Merlyn435 and ESC uses standard 20x20mm mounting hole distance.

1. Place 4x M2 Nuts into the recesses in the bottom frame plate.

2. Push rubber grommets into the flight controller and ESC mounting holes.

3. Push 4x M2 20mm screws through the adapter plate, through the rubber grommet, and through the bottom plate into the M2 nuts..

The VTX mounts to the rear of the frame.

1. Place 4x M2 Nuts into the recesses in the bottom frame plate.

2. Push rubber grommets into the VTX mounting holes.

3. Push 4x M2 10mm screws through rubber grommets, down through the bottom plate, and into the M2 nuts.

1. Mount the four 1505 4300KV motors to the arms using 16x M2 6mm screws (4 per motor). Ensure the screws do not touch the motor windings inside the bell.

2. Mount the HQPROP 3x3x3 propellers. Pay attention to motor rotation directions (depending on your betaflight configuration, it could either be prop in or prop out). Fasten each prop with 2x M2 6mm screws.

1. Mount the analog FPV camera to the cage using 2x M2 6mm screws.

2. Mount the camera cage to the bottom frame using 2x M2 6mm Self Tapping screws.

3. Mount the 6x M3 20mm Female to Female Brass Standoffs and secure with 6x M3 6mm screws to the bottom plate.

4. Press fit the antenna holder to the brass standoffs, then insert the antenna and connect the antenna to the VTX.

5. Press fit the GPS module into the bracket.

6. Mount the top plate and secure with 6x M3 6mm screws.

7. Mount the GPS module and bracket underneath the top plate and secure with 4x M2 6mm Self Tapping screws.

8. Insert 2x M2 6mm Self Tapping screws to secure the top plate to the camera cage.

Note: The prices in USD are converted as of 22 August 2026 and may fluctuate. Promo codes will be applied before checkout to bring the costs down. And yes, the costs of separate components are cheaper than JLCPCB assembly.

• Flight Controller Total: $89.42
• ESC Total: $33.95
• Shipping Total: $26.50
• Drone Parts Total: $134.16